The Potentiometer is an electric instrument that used to measure the of a given cell, the internal resistance of a cell. And also it is used to compare EMFs of different cells. Chennai express songs naa songs in telugu. It can also use as a in most of the applications. These potentiometers are used in huge quantities in the manufacture of electronics equipment that provides a way of adjusting so that the correct outputs are obtained. Although their most obvious use must be for volume controls on radios and other electronic equipment used for audio.
Potentiometer Why is Potentiometer chosen over Voltmeter to measure the potential (EMF) of a cell? When we use Voltmeter, current flows through the circuit and because of the internal resistance of the cell, always terminal potential will be less than the actual cell potential. In this circuit, when the potential difference is balanced (using a Galvanometer null detection), no current flows in the circuit, so the terminal potential will be equal to the actual cell potential.
So we can understand that the Voltmeter measures the terminal potential of a cell, but this measures actual cell potential. The schematic symbols of this is shown below. Schematic Symbols of a Potentiometer Construction and Working Principle The potentiometer consists of a long resistive wire L made up of magnum or with constantan and a battery of known EMF V. This voltage is called as driver cell voltage. Connect the two ends of the resistive wire L to the battery terminals as shown below; let us assume this is a primary circuit arrangement. One terminal of another cell (whose EMF E is to be measured) is at one end of the primary circuit and another end of the cell terminal is connected to any point on the resistive wire through a galvanometer G.
Now let us assume this arrangement is a secondary circuit. The arrangement of the potentiometer as shown below. Construction of Potentiometer The basic working principle of this is based on the fact that the fall of the potential across any portion of the wire is directly proportional to the length of the wire, provided wire has uniform cross-sectional area and the constant current flowing through it.“When there is no potential difference between any two nodes there is electric current will flow”. Now the potentiometer wire is actually a wire with high resistivity (ῥ) with uniform cross-sectional area A.
Thus, throughout the wire, it has uniform resistance. Now this potentiometer terminal connected to the cell of high EMF V (neglecting its internal resistance) called driver cell or the voltage source.
Let the current through the potentiometer is I and R is the total resistance of the potentiometer. Then by Ohms law V=IR We know that R= ῥL/A Thus, V= I ῥL/A As ῥ and A are always constant and current I is kept constant by a rheostat. So L ῥ/A=K (constant) Thus, V= KL.
Now suppose a cell E of lower EMF than the driver cell is put in the circuit as shown above. Say it has EMF E. Now in the potentiometer wire say at length x the potentiometer has become E. E= L ῥx/A=Kx When this cell be put in the circuit as shown above figure with a jokey connected to the corresponding length (x), there will be no flow of current through the galvanometer because when the potential difference is equal to zero, no current will flow through it. So the galvanometer G show null detection.
Then the length (x) is called the length of the null point. Now by knowing the constant K and the length x. We can find the unknown EMF. E= L ῥx/A=Kx Secondly, EMF of two cells may also be compared, let the first cell of EMF E1 given a null point at a length= L1 and the second cell of EMF E2 show a null point at length= L2 Then, E1/E2= L1/L2 Types of Potentiometers A potentiometer is also commonly known as pot.
PC minimum system requirements VST or RTAS host software Pentium class 1.5 GHz processor with SSE2 support* 2GB of RAM (4GB or more highly recommended) Display with 1024-by-768 or higher resolution Windows XP SP3, Windows Vista, Windows 7 or later Available disk space 4GB to install the plugin and factory content Approx. Refx nexus 2 full torrent download.
These potentiometers have three terminal connections. One terminal connected to a sliding contact called wiper and the other two terminals are connected to a fixed resistance track. The wiper can be moved along the resistive track either by use of a linear sliding control or a rotary “wiper” contact. Both rotary and linear controls have the same basic operation. The most common form of the potentiometer is the single turn rotary potentiometer. This type of potentiometer is often used in audio volume control (logarithmic taper) as well as many other applications. Different materials are used to construct potentiometers, including carbon composition, cermet, conductive plastic, and the metal film.
Potentiometer Rotary Potentiometers These are the most common type of potentiometers, where the wiper moves along a circular path. Rotary Potentiometers.
Linear Potentiometers In these types of Potentiometers the wiper moves along a linear path. Also known as slide pot, slider, or fader. Linear Potentiometers Applications of Potentiometers Potentiometer as a Voltage Divider Voltage Divider The potentiometer can be worked as to obtain a manual adjustable output voltage at the slider from a fixed input voltage applied across the two ends of the potentiometer. Now the load voltage across RL can be measured as VL= R2RL. VS/(R1RL+R2RL+R1R2) Audio Control Sliding potentiometers, one of the most common uses for modern low-power potentiometers are as audio control devices.
Both sliding pots (faders) and rotary potentiometers (knobs) are regularly used to frequency attenuation, adjust loudness and for different characteristics of audio signals. Html5 plugin for firefox. Audio control Television Potentiometers were used to control the picture brightness, contrast, and colour response. A potentiometer was often used to adjust “vertical hold”, which affected the synchronization between the received picture signal and the receiver’s internal sweep circuit. Transducers One of the most common application is measuring of displacement. To measure the displacement of the body, which is movable, is connected to the sliding element located on the potentiometer. As the body moves, the position of the slider also changes accordingly so the resistance between the fixed point and the slider changes. Due to this the voltage across these points also changes.
Potentiometer as a Transducer The change in resistance or the voltage is proportional to the change in the displacement of the body. Thus the voltage change indicates the displacement of the body. This can be used for the measurement of translational as well as well rotational displacement. Since these potentiometers work on the principle of resistance, they are also called as the resistive potentiometers. For example, the shaft rotation might represent an angle, and the voltage division ratio can be made proportional to the cosine of the angle. Thus, this is all about types of Potentiometer, its construction and applications.
We hope that you have got a better understanding about this information. Furthermore, any queries regarding this concept or, please give your valuable suggestions by commenting in the comment section below. Here is a question for you, What is the function of rotary potentiometer? Hi nishant I sincerely appreciate your kind response regarding my article And once again please visit our domestic website For more details please contact to Sathish on +011 or you can email us on An electric generator produces E.M.F inside the generator in the armature which is due to the change of flux in the armature coils and this is a perfect example of E.M.F. EMF=k.Φ.w.where k— a constant, Φ— flux per pole, w—speed of the rotor. Here is no term of resistance over here.
So, emf is generated by a source. Voltage is just the potential difference between two points in a circuit. Voltage=I.R And here comes the play of resistance and if it is an a.c circuit then resistance will be replaced by impedance. You just put a voltmeter in two terminals of your electronic/electrical circuit you will get the voltage difference between that two points. One more important thing is that we can’t find voltage of a single point.
UNIT-I Measuring Instruments Classification – deflecting, control and damping torques – Ammeters and Voltmeters – PMMC, moving iron type instruments – expression for the deflecting torque and control torque – Errors and compensations, extension of range using shunts and series resistance. Electrostatic Voltmeters-electrometer type and attracted disc type – Extension of range of E.S.
UNIT –II Instrument transformers CT and PT – Ratio and phase angle errors – design considerations Type of P.F. Meters – dynamometer and moving iron type – 1-ph and 3-ph meters – Frequency meters – resonance type and Weston type – synchroscopes. UNIT –III Measurement of Power Single phase dynamometer wattmeter, LPF and UPF, Double element and three element dynamometer wattmeter, expression for deflecting and control torques – Extension of range of wattmeter using instrument transformers – Measurement of active and reactive powers in balanced and unbalanced systems. UNIT –IV Measurement of Energy Single phase induction type energy meter – driving and braking torques – errors and compensations – testing by phantom loading using R.S.S. Three phase energy meter – trivector meter, maximum demand meters. UNIT – V Potentiometers Principle and operation of D.C. Crompton’s potentiometer – standardization – Measurement of unknown resistance, current, voltage.
Potentiometers: polar and coordinate types standardization – applications. UNIT – VI Resistance Measurements Method of measuring low, medium and high resistance – sensitivity of Wheatstone’s bridge – Carey Foster’s bridge, Kelvin’s double bridge for measuring low resistance, measurement of high resistance – loss of charge method.
Dc Motor Potentiometer
UNIT –VII A.C. Bridges Measurement of inductance, Quality Factor – Maxwell’s bridge, Hay’s bridge, Anderson’s bridge, Owen’s bridge. Measurement of capacitance and loss angle – Desauty bridge. Wien’s bridge – Schering Bridge.
UNIT – VIII Magnetic Measurements: Ballistic galvanometer – equation of motion – flux meter – constructional details, comparison with ballistic galvanometer. TEXT BOOK: Electrical Measurements Notes – EM Notes – EM Pdf Notes. Electrical Measurements and measuring Instruments – by E.W. Golding and F.C. Widdis, fifth Edition, Wheeler Publishing. Electrical & Electronic Measurement & Instruments by A.K.Sawhney Dhanpat Rai & Co. REFERENCE BOOKS: Electrical Measurements Notes – EM Notes – EM Pdf Notes.
Electrical Measurements – by Buckingham and Price, Prentice – Hall. Electrical Measurements by Harris. Electrical Measurements: Fundamentals, Concepts, Applications – by Reissland, M.U, New Age International (P) Limited, Publishers.
Note:- These notes are according to the r09 Syllabus book of.In R13,8-units of R09 syllabus are combined into 5-units in r13 syllabus.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |